Daily Home Renovation Tips每日家裝修秘訣

In在…內 Part 5第5部分 we had completed the installation of the 3M Adhesive Stud hardware and waited 24 hours to achieve 90% bonding strength (per the manufacturer’s web site).我們已經完成了安裝的3個月種膠粘劑的硬件和等待24小時，以達到90 ％ ，粘結強度（每製造商的網站） 。 We are now ready to complete the installation of the EZ Snap solar blind on our test window.我們現在已經準備好完成安裝的EZ管理單元太陽能盲對我們的測試窗口。

We started by simply applying the male part of the EZ Snap fasteners onto the adhesive studs that were already on the window frame from the prior day.我們已開始由簡單應用的一部分，男性的EZ管理單元緊固件上膠粘劑釘表示，已在窗框，從之前一天。 You could actually hear and feel the fastener ’snap’ onto the adhesive stud.你其實可以聽到和感受到緊固件'管理單元'上膠粘劑種。 It took I would say a medium amount of pressure.花了我會說一個中等數額的壓力。 All of the fasteners were installed on the adhesive studs for our test window in about 2 minutes.所有的緊固件均安裝在膠粘劑釘，為我們的測試窗口，在大約2分鐘。

Here is what it looks like close up for one of the male fasteners on top of the adhesive stud.這裡是什麼，它看起來像關閉了其中的男性緊固件再加上膠粘劑種。

And, for comparison, in the picture below the top adhesive stud does not yet have the male fastener applied while the lower hardware does have the  male fastener applied.和，以作比較，在下面的圖片頂端膠粘劑種還沒有男性的緊固件適用，而較低的硬件是否有男性緊固件的應用。

Now, let’s talk about the measurements for the solar mesh.現在，讓我們談談測量太陽網格。 Our windows are recessed within the face of the brick.我們的Windows是休會內部面對磚。 And, for aesthetics I wanted the mesh to cover not only the window but also the window frame. ，並為美學我希望網格不僅涵蓋窗口，而且窗框。 So I planned on having an extra 1/2 inch of solar mesh around the outside of the window frame.因此，我計劃在有一個額外的1 / 2英寸太陽能網格周圍以外的窗框。

In measuring the opening in the brick for the window frame I had the following measurements:在衡量開放，在磚為窗框，我有以下測量：

• Left side height - 71 inches左邊的高度-七十一英寸
• Right side height - 71 inches右側的高度-七一英寸
• Top width - 4 feet 1/2 inch頂端寬度-四英尺1 / 2英寸
• Lower width - 4 feet 1 inch較低的寬度-4英尺1英寸

Yes, the lower horizontal dimension was slightly wider than the top horizontal dimension.是的，較低的橫向尺寸略較頂端的橫向層面。 Good thing this product can, as the manufacturer claims, fit any size or shape of window, even one that is not a perfect square like mine一件好事，此產品可作為製造商索賠，適合任何大小或形狀的窗口，即使是一個不是一個完美的廣場一樣，排雷

I then proceeded to cut the solar mesh.然後我開始削減太陽能網格。 There are one of two ways you can go.有兩種方法之一，您可以去。 Either use a sharp pair of scissors or a sharp utility knife and a straight edge.要么使用一個尖銳的對剪刀或大幅美工刀和一個直邊。 I chose the latter for two reasons.我選擇了後者，原因有兩個。 First, I had lots of unused heavy duty replacement blades for my utility knife.首先，我有很多未使用的重型更換刀片我的美工刀。 And, second, I did not trust myself to cut a straight line using the scissors.和，第二，我不信任自己，以削減一條直線，用剪刀。

In fact, as discovered, visible in the solar mesh are the fabric lines.事實上，正如發現，可見光，在太陽能網格是織物線。 So, I could have used this as a guide to use the scissors and cut a straight line.所以，我可以以此為指南，使用剪刀和削減一條直線。 Again, the straight line is only for aesthetics.再次，直線是只為美學。

Once the mesh was cut based on the dimensions above, I proceeded to install on top of the male fasteners.一旦網格被削減的基礎上，尺寸以上的，我著手安裝在頂部的男性緊固件。 This was a very quick process (2 minutes?) as it was a small window.這是一個非常快速的過程（ 2分鐘？ ） ，因為這是一個小窗口。 I first positioned the mesh over the window to determine exactly where it would be applied covering all of the window frame and then simply pushed the mesh onto each male fastener with little effort.首先，我定位網格以上的窗口，以準確確定，而將適用於涵蓋所有的窗框，然後簡單地把網格上每個男性緊固件很少的努力。

I started with the male EZ Snap fasteners along the top window frame, followed by those on the vertical side window frames, in parallel with each other and lastly with the fasteners along the bottom frame.我開始與男性的EZ管理單元緊固件沿頂端窗框，其次是那些在垂直方窗框，在同向平行對方，最後與緊固件沿底部框架。 The picture below shows the same upper left corner with the solar mesh installed prior to the application of the cap hardware.下面的圖片中顯示相同的左上角與太陽網格安裝前的應用上限的硬件。

The next step was to push the caps onto the protruding male fastener.下一步是把警帽上伸出男性緊固件。 This actually was the hardest part for me and took a significant amount of pressure.這實際上是最難的一部分，對我來說並採取了大量的壓力。 Below is a picture of the portion of the solar blind with the cap applied to the EZ Snap fastener on the right compared to the fastener on the right that does not yet have the cap applied.下面是一張圖片的部分太陽能盲與上限適用的EZ管理單元緊固件在右邊相比，緊固件上的權利還沒有上限適用。

I even used a small hammer to ensure I had the caps on sufficiently tight.我什至用一個小錘子，以確保我有足夠的上限，就緊張。 (WARNING: Using a hammer to install the caps is not recommended. I’ll explain why in a future article so you can avoid what you can likely guess happened to me….not on the test window but on one of the other windows) （警告：使用錘子安裝警帽是不推薦，我會解釋為什麼在未來的文章，使您可以在避免什麼，您可以猜測可能發生的事情，我… … 。不會在測試窗口，但對其中的其他Windows ）

And there you have it.有你有。 The EZ Snap solar blind fully installed on our test window.的EZ管理單元太陽能盲完全安裝在我們的測試窗口。

But, how does it look from the inside?但是，它如何看從內？ And, is there any noticeable reduction in the sun’s UV rays and heat build up?和，是否有任何顯著減少在太陽的紫外線和熱量建立？ We will discuss this in our next article in this series.我們會討論這在我們的下篇文章，在這一系列。

To continue with this series of articles on exterior solar blinds, simply select this link to繼續與這一系列的文章，外部太陽能百葉窗，只需選擇此鏈接 Part 7第7部分 . 。